Fish Tank Pump

How To Make A Water Pump Do It Yourself For The Aquarium

August 24, 2019

How to make an air pump for the aquarium do it yourself

Coming to the question of a water pump with their own hands, the undoubted advantages include:

  • financial component.
    We will assemble these devices at home almost from scrap materials. Consequently, it is quite cheap;
  • repair and replacement of nodes.
    In the same way as we assembled the device, we will be able to repair it as well. Accordingly, there will also be no need to purchase a new device;
  • noise level.
    With the help of shock-absorbing materials and fasteners, we will reduce the vibration in the device to the maximum;
  • power.
    Under a different volume of water, we will be able to create an individual, suitable power vodushny pump.

There are a lot of advantages in the manufacture of a water pump and they are quite significant.

Consider the detailed instructions for the manufacture of a four-chamber water pump for an aquarium.

For the manufacture will need the following tools and materials:

  • plastic bottle with a large neck – 4 pcs ;
  • round air balloon – 4 pcs ;
  • gum – 4 pcs ;
  • 5-cc syringe – 4 pcs ;
  • plastic size 10×15 cm – 1 pc ;
  • plastic bottle cap – 1 pc ;
  • a piece of plastic measuring 5×5 cm – 1 pc ;
  • clips – 5 pcs ;
  • dropper – 1 pc ;
  • gearbox with engine – 1 pc ;
  • switch – 1 pc ;
  • battery – 1 pc;
  • wires – 2 pcs ;
  • soldering iron;
  • knife;
  • Super glue;
  • hot melt glue

The maintenance of aquarium fish is not as simple as it seems at first glance. For full care of the fish will need to create conditions as close as possible to the natural.

For example, to saturate water with air and its constant mixing it is necessary to install a water pump.

And you can make it yourself and thus save a significant amount of funds.

It is possible to create all the conditions necessary for aquatic inhabitants without installing additional equipment. However, it is quite difficult for non-professional aquarists to take all the inhabitants and plants to create an ecological environment and take a considerable amount of time. Installing a water pump will solve these problems and can be done without the help of professionals.

To build an air pump for the aquarium with your own hands, you will need the following tools and accessories: – a small electric motor; – eccentric;

Aquarium air pump is manufactured in several different ways. Consider the most simple and common. To create a water pump, you must perform the following steps:

  1. Take a small electric motor and connect it to the power supply. It is recommended to use an engine with a voltage of no more than 12 volts, so that in the event of a long shutdown, the power supply remains able to be powered from the battery for the car.
  2. Further, an eccentric is fixed on the surface of the electric motor, thanks to which a small pump is set in motion.

How To Make A Water Pump Do It Yourself For The Aquarium

The considered variant will be most appropriate in that situation if it is necessary to manufacture an air pump for an aquarium silent. If the presence of noise is not your main criterion, then you can use another method to create a water pump:

  1. As an additional equipment, it is necessary to find an electromagnet. For example, you can use a small magnetic starter that operates at a frequency of 50 Hz from a voltage of 220 volts.
  2. Then it is necessary to attach a small pump to the electromagnet, the membrane of which will start moving from side to side with a similar frequency of 50 Hz. It is through this movement that the pump pumps air, and thus aeration of the water is carried out. The extra noise is generated due to the operation of the electromagnet and for this reason this method is less common.

A self-made water pump will not only be cheaper than ready-made counterparts, but may also be much more efficient than other devices, and will also be easier to repair.

In most cases, the aquarium is installed in those areas where people are constantly. First of all, it should be borne in mind that the water pump must function continuously and therefore do not neglect the quality of its manufacture.

If you built a water pump using an electromagnet that creates excessive noise, then such an apparatus can be removed into a closed cabinet. For this purpose, a long duct is useful. In addition, the air pump for the aquarium air can be installed in the box from the old film, which will contribute to reducing the force of the shock wave.

A wooden box will hide the structure from sight and affect the sound insulation.

You also need to know that the self-made air pump for the aquarium must exercise moderate control of the air flow. It is recommended to pre-calculate the power of the engine being built in from the formula of 0.5 l / h per liter of water. As mentioned earlier, it is advisable to put a low-voltage water pump in the aquarium (not more than 12 volts).

It is important that in the presence of a large number of plants inside the aquarium and when oxygen is supplied, the use of a water pump is not necessary during the lighting period.

Usually in such cases it is included only at night, when the plants stop producing oxygen and start consuming it on a par with the fish.

In order to prevent the water from being poured into the water pump due to the return thrust when the device is turned off, it is necessary to install a non-return valve on the tube going towards the sprayer.

After making the water pump, it is necessary to properly fix it inside the aquarium. This procedure is quite easy and can also be done independently. Before direct installation, you should select in advance the place where the device will be located. The water pump can be placed either above the water surface or in a small enclosed space next to the aquarium.

Sprays and hoses are recommended to be fixed on the bottom with a heavy object (a shell or a large stone). In that case, if the sprayer can float upward, then the water will be poorly saturated with air.

Hoses connected to the water pump should be selected from silicone or elastic rubber. If the part of the hose in the water hardens, then it must be replaced with a new one.

It is very important that to ensure the normal life of the inhabitants of the aquarium should be used exclusively special hoses designed for aquarium.

Check whether the fish have enough oxygen in the water, you can observe their behavior. Most species of aquarium fish prefer to move near the bottom or in the middle of the water space.

If all the inhabitants of the aquarium periodically float to the surface to swallow oxygen, then it is imperative to revise the design of the water pump.

The air pump for the aquarium, created with his own hands, simultaneously performs several functions. First of all, it provides optimal living conditions for the fish in the aquarium. After all, they require constant purification of water and supply it with oxygen. In addition, a homemade device significantly reduces the cost of caring for fish.

With certain knowledge, it is possible to create optimal living conditions for aquatic inhabitants without using a water pump. Good knowledge of the correct use of the necessary algae and calculations of the amount of water per inhabitant are required.

For a person who is engaged in aquariums unprofessional, this is rather complicated information that is practically impossible to apply in practice. That is why making a water pump for the aquarium with your own hands will be an ideal option that will prolong the life of the fish and will relieve you of unnecessary problems.

In order to build such a construction, you need a few elements:

  1. The motor is small in size, with a capacity of only 12 volts.
  2. Eccentric, which will provide rotational motion.
  3. Water pump.

Having prepared all the necessary materials, you can begin to manufacture the simplest design.

It is not recommended to use powerful engines, they will not give any advantages, but they will cause quite a lot of noise.

Read more:  What Is A Water Pump For?

Manufacturing process

How to make a water pump? There is an answer to this question, which provides for a clear sequence of actions.

It can be noted that there are a lot of ways to manufacture the device, but it is worth paying attention to the simplest ones.

Option one involves the following actions:

  1. Take a small electric motor and connect it to the power system. As already noted, it is recommended to use a device whose power will not exceed 12 volts. This is also relevant because with a long outage of electricity for its operation, you can use the most ordinary battery or battery.
  2. Further, an eccentric is attached to the engine surface. It will set in motion the pump, which will ensure the process of circulation of water and supply it with oxygen.

This option is silent, the functioning will not disturb the rest during a night’s sleep. If extraneous sounds absolutely do not bother the owner, then you can resort to using the second option:

  1. First you need to acquire additional equipment, an electromagnet will act as it. A magnetic starter with a frequency of 50 Hz will be quite enough at a voltage of 220 volts.
  2. A pump is connected to this electromagnet, the membrane of which begins to move under the action of the magnet with the same frequency. As a result of this process, air is pumped into the pump.

How To Make A Water Pump Do It Yourself For The Aquarium

Because of the functioning of the magnet, sound effects are created that make the method less attractive.

How does the air pump for the aquarium

Aquarium fish for the full life requires optimal living conditions. They need constant oxygen, but sometimes the water surface and the number of plants inside is not enough. In this case, you need to purchase an additional device that will help to saturate the water with oxygen – this function is carried out by a water pump.

It is used for the following tasks:

  1. Providing aeration. The rising oxygen bubbles saturate the water with oxygen.
  2. Stirring the water. Even a slight turbulence levels the temperature of the water at all levels. In addition, fluid retention is not allowed.
  3. Lack of formation of a film on a water edge. Similar problems arise from bacteria and dust.
  4. Imitation of the flow. This allows you to create conditions close to natural.

Such an adaptation is important not only for large aquariums, but also for small ones, but the power should be different. The water pump should not work all the time; it is enough to turn it on for a while twice a day. If the ambient air temperature is high, then it is recommended to do it more often, since when water is heated, oxygen is consumed faster.

Aquarium inlet pump is a device that is designed to enrich the water with oxygen.
The principle of operation of this device is as follows:

  1. Through the tubes, which are located at one end above the water, and the other attached to the pump, located at the bottom of the aquarium, oxygen enters. The air pressure is regulated by means of valves and clamps.
  2. The upper part of the pump is a sprayer made of an abrasive substance, through which the aquarium is aerated by forming a large number of bubbles.
  3. The bubbles burst on the surface of the water and thus destroy the bacterial film, moreover, they mix layers of water during the movement.

Homemade air pump for aquarium

Despite the advantages, these devices may have the following problems when working:

  1. Noise increase during operation. Occurs when the valves are dirty. This reduces the power of the device. If even minimal manifestations of atypical noise occur, the device must be disassembled and cleaned or taken to service.
  2. Damage to the membrane. This problem leads to increased noise and problems with water aeration. In this case, replacement parts will be required.
  3. Problems with the filter. The reasons may be different – from problems with power supply to the destruction of the rotor due to mechanical damage. All this requires repair with the replacement of damaged parts.

To avoid these and other problems with the aquarium, it is better to entrust its care to professionals who can identify the problem at first and correct the situation with minimal waste. Now you will be able to choose the right water pump without any problems, which will meet all the requirements, and with a strong desire to even make it yourself.

Piston professional water pumps are more powerful and are designed for aeration in large-capacity aquariums, over 200 liters, for example. At the same time they are the most noisy, since the movement of the piston is always accompanied by a rather loud sound.

Membrane air pumps are almost noiseless, their work is based on the movement of a rubber membrane that pumps air into the outlet tube.

Water pumps are also distinguished by the type of power source: either from a household electrical network or from batteries. There are also external and internal devices, if we consider the method of installation.

The price range of these technical devices is also quite wide – from several hundred to 20 thousand.

rubles (for example, Italian pump Sicce MULTI), depending on the design, configuration, power and other characteristics.

At the first stage of the operation of the apparatus, it is necessary to achieve accumulation of a certain amount of air. Next, it is fed to the aquarium.

The required sizes

In a small or medium size aquarium, you can install any model of water pump you need. He will be able to supply the fluid with the necessary components and help to avoid green deposits in the aquarium.

As a rule, such models do not make noise and do not spoil the aesthetic appearance.

Varieties

The main classification divides water pumps for aquariums into such groups: diaphragm, piston and pumps. They differ in the principle of work, the power of noise and price.

Piston

The principle of operation is the movement of the piston, through which the air is pushed out. Rotational movements of the piston shaft become oscillatory. Such changes help to achieve the desired air supply. This is an ideal air pump for an aquarium, which is located in the bedroom, because it produces a minimal amount of noise, but it is more expensive than a membrane one.
The advantages are:

  • durability;
  • almost silent work;
  • high performance;
  • can be used for large aquariums.

The disadvantages of these devices are as follows:

  • high energy costs;
  • great value.

Membrane

The principle of operation is the movement of air from the chamber connected to the membrane due to pressure drops, which is created due to the magnet oscillations.
Pluses of this device:

  • low energy consumption;
  • easy repair;
  • cheapness.
  • low power;
  • loud noise during operation.

Materials and tools for manufacturing

To make an aquarium inlet pump with your own hands, you will need tools at hand. The principle of operation of a water pump in an aquarium is simple: it accumulates air in it, and then feeds it into the pond. Based on this, it is very easy to navigate what kind of materials and tools you may need for self-production.

Materials for creating an air pump air:

  • capacity for air (a balloon or a chamber from a ball, bicycle wheel);
  • small electric motor;
  • any pump pear;
  • dropper tube;
  • eccentric;
  • dropper clamp;
  • tee for connecting tubes;
  • clamps.

Instrument creation tools:

This is not all possible items that may be needed for a homemade device. Note that the quantity of materials required often depends on the type of product. Therefore, to get started, read the different instructions.

How to make an air pump for the aquarium with your own hands? In fact, this task will cope any. The easiest way to create it is based on a pear or a camera.

Simple option

To create this design, take the air tank, for example, the camera from the wheel, tubes and clamps from droppers, pump and tee.

  1. Cut the tube from the dropper into three pieces. Make one of them a little longer – it will be lowered into the container.
  2. In a long section, with a cigarette lighter, solder the edge and make a lot of holes at its tip with a needle. To prevent the duct from floating up, tie a small weight on its tip. Put the clip on the same piece.
  3. Connect all three segments of the tube with a tee, fasten them with clamps.
  4. Attach a pear or a pump to one of the two segments, and an air tank to the other. Caution: on the hose that goes to the pear, also secure the clip from the dropper.
  5. Pump air through the pump into the air tank, shut off the inlet flow. A long hose with holes drop into the aquarium and open the output stream with a clip from the dropper.
Read more:  How To Choose An Air Pump For The Aquarium

How To Make A Water Pump Do It Yourself For The Aquarium

Your device for the supply of air in the reservoir is ready. You can adjust the flow with the help of a clip from the dropper. It is necessary to pump a couple of times a day – it all depends on the size of the air tank.

  1. Take a small plastic bottle, an electric motor, a cooler, a dropper tube, glue. You will also need wires, batteries and a jack for them, the power button. Cut the bottle in two halves.
  2. Using a soldering iron, attach the wires to the motor, and attach the cooler to it. The resulting device is secured with superglue inside the bottle.
  3. Attach a tube with a sealed end and a lot of small holes in the bottom to the neck of the bottle.
  4. Attach a button and a battery socket to the wires and close the half of the bottle with the second part of it.

The device made in this way will help out not only on the road. He will help a lot when turning off the lights in the house.

12 volts

When self-creation based on the electric motor, it is desirable to use a 12 volt motor. Then in case the lights are turned off in the house, you can even connect it to the car battery. Under normal conditions, it works from the electrical network using a power supply.

Attach an ordinary eccentric to the motor shaft, attach a pump to it – for example, a syringe or an improvised device. The shaft will move the piston, and it will pump air.

Silent

Homemade air pump for the aquarium can be quiet. To do this, the usual fixture just need to hang inside the jar. To do this, make three holes in the lid: one for the duct, the second for the wire, and the third for the hook on which you hang it. Assemble the design and use on health.

In fact, a completely silent water pump is a legend. But this method will significantly reduce the volume of this device.

Sorry, there are currently no polls available.

To create a device, you will need to purchase the following components in advance:

  • Chamber of rubber.
  • Hand pump with car or pedal type.
  • Kranik with three moves.
  • A tube from a medical dropper.

How To Make A Water Pump Do It Yourself For The Aquarium

To tee need to bring the tube. They will connect it to the hand pumps, the ball and the outlet of the hose. At the end of the dropper placed restrictive tube. However, before the tube will need to make a few holes. Through them in the future will go the air.

The air in the system begins to collect after the opening of the line that connects the pump with the ball. The camera should not be pumped to capacity. It should remain soft.

In the next step, you will need to open access from the camera to the outlet tube. Manipulation will allow to remove the accumulated part of the air into the aquarium. The diameter can be adjusted by means of a pre-set clamp. It should be in the outer part and connect to the tee. The feed rate is adjusted empirically.

The disadvantage of using this variant of the device is the need to inflate the camera.

If the aquarium is aerated into 100 liters, the procedure will need to be carried out twice a day. The system can not be left offline for a long period.

How to choose

Today the market offers a huge number of different air pump for the aquarium. To avoid mistakes, you need to know what to look for during the acquisition:

  1. Performance. This indicator shows the amount of air that the device surpasses for a certain time interval. Performance depends on the number of fish and their species. The optimal rate is 0.6 l / h per liter of water. To increase this figure, a biofilter must be present in the tank.
  2. Power. Determines the performance and the greatest amount of energy that is needed for the full operation of the device. This indicator indicates the maximum permitted immersion depth of the device. The most widespread devices with a capacity of 3-10 watts.
  3. The volume of the aquarium. The water pump should be selected based on the size of the tank where the fish will live. The smaller the aquarium, the more compact the water pump should be.
  4. Manufacturer. Customer testimonials point to the popularity of German high power brands, which are also regulated. Also popular are Italian fixtures, which are also not very noisy.

How to install a water pump in the aquarium

How To Make A Water Pump Do It Yourself For The Aquarium

Important is the correct installation of the device. The first thing to do is to decide where the water pump will be. It can be placed above the surface of the water or in a tank that is located outside the aquarium. Submersible water pumps should be installed in such a way that there are no problems with cleaning that should be done from time to time. In order not to create a lot of noise, foam rubber or foam is laid on the bottom. The tube is pressed against a shell or pebble.

Device Installation Diagram:

  • The sprayer will need to be fixed at the bottom of the vessel. It is also allowed its location on the wall. For this purpose, additional suction cups are used.
  • To the main unit attach the hose and spray. Removal of the required amount of air will be made through the tube. Technological holes are preliminarily formed in the water pump.
  • The water pump is installed outside the aquarium. The water level must be below the location of the device itself. If this condition is not possible, then you will need to include a check valve in the system. Due to this, the liquid will not be able to get inside the device and disrupt its functioning. This will prevent serious damage.

Water pump care

In order for the water pump to work the most amount of time, it needs systematic care, which consists of the following manipulations:

  • air filter replacement;
  • monitoring the condition of rubber membranes;
  • regular cleaning of diffusers;
  • checking the condition of air hoses.

The device will last a long time if properly handled. To do this, you need to adhere to the following scheme:

  • Air filter will need to be changed regularly. The device is located at the output of each device.
  • Membranes also tend to break down quickly. If they are not replaced in time, the entire water pump may break. It is difficult to find a repair kit that will fit a particular model.
  • Diffuser needs constant cleaning. In this case, it is possible to significantly reduce the resistance that is formed in the system.
  • Air hoses tend to fail. Their replacement should also be carried out as needed.

aquarium inlet pump with their own hands

That is why when it comes to self-manufacturing aquarium water pump, it causes some confusion.

How To Make A Water Pump Do It Yourself For The Aquarium

Meanwhile, making a small device with your own hands for forcing air into the aquarium water is quite capable of almost anyone. But how to do it? And in general, why is it needed? Let’s try to figure it out.

Being a device for creating pressure (compression), the unit delivers air directly into the aquarium environment. This process is very important for ornamental flora and especially fauna. Fish are known to breathe through the gills with oxygen dissolved in water. If there is little oxygen in aqua, the very existence of pets will be at risk.

Read more:  What To Do When Turn Off The Electricity

In the domestic artificial reservoir, such air saturation is performed using aeration — forced, controlled supply of air flow into the aquarium water. Moreover, the smaller the air bubbles emerging from the water pump, the more dissolved air is formed in the water space.

One can say this: a water pump is an ordinary air pump.

The price range of these technical devices is also quite wide – from several hundred to 20 thousand rubles (for example, the Italian pump Sicce MULTI), depending on the design, equipment, power and other characteristics.

Before you make your own air pump for an aquarium, we will prepare the following materials and tools: a plastic bottle cap, a piece of rubber, a wooden frame base, a plastic tube, a small motor and an old battery for it, as well as hot glue and the usual balloon, still need an old plastic card.

To make an aquarium inlet pump with our own hands, we remove the seal from the plastic cover and apply space under the holes with a marker. We make holes with scissors.

How To Make A Water Pump Do It Yourself For The Aquarium

The plastic tube should fit there.

Next, we cut a piece of a horseshoe from a piece of rubber seal, which we glue to the inside of the cover.

With a plastic card with your own hands, you need to make a part of an aquarium water pump in the form of a circle, slightly smaller than the lid.

To one part of the plastic with a hot glue we fix a small stick from the candy, with the other side glue everything to the rubber part of the drum.

Cut off a small piece of glue for the gun. We make two holes with an awl: one in the center, the second closer to the edge.

In the central insert the motor in the side of a small piece of wire.

It remains only to connect the tube and the motor, and the aquarium inlet pump is ready with your own hands.

To date, used several options for air pump. With their help, it is possible to create comfortable conditions for the life of the fish. When choosing to pay attention to the type of design:

  • Piston. Professional option, which is advisable to use when the volume of aquariums more than 200 liters. Their disadvantage is the high level of noise. The piston at the time of movement can not create discomfort to others.
  • Membrane. Does not create noise and works on the basis of a membrane made of rubber. It drives the air in the tube.

The device is also installed on the outer or inner side of the aquarium. The method should be considered separately.

How To Make A Water Pump Do It Yourself For The Aquarium

The price of the system depends on its capacity. It starts at 100 and ends at 20 thousand rubles. The water pump is improved by changing the design, power and other performance characteristics.

There is a mistaken opinion that aquarium fish do not require care. In fact, this occupation is troublesome. Care can be simplified through the use of modern devices. For example, with filters, water will rarely need to be changed. Additionally, it will be necessary to arrange lighting, thermoregulation and a water pump for air supply.

Which air pump for the aquarium is better

  1. Easy to assemble.
  2. Cheap design.
  3. Elementary adjustment, maintenance or repair.
  4. Low price.
  5. You can achieve a fairly low noise level.

All this suggests that do not be afraid to create equipment for your reservoirs. So you can create equipment, directly for the needs of a specific water capacity, without spending extra finances.

Despite the fact that there are a huge number of different water pumps on the market, the most popular brands can be distinguished from them, which will be described below.

Barbus

water pumps manufactured in China.

Barbus SB-348A. Powered by a battery that needs to be charged every 12 hours. It has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 240 l / hour;
  • power – 12 W;
  • weight – 2.25 kg.
  • minimum noise level;
  • work from a network or the battery;
  • good wear resistance;
  • There is an adjustment of the air flow.
  • big weight;
  • high power consumption.

Equipped with a smooth power control and reduced noise. It has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 360 l / hour;
  • power – 10 W;
  • weight – 0.95 kg.
  • air-compression system ensures long service life;
  • multi-level housing walls ensure low noise level;
  • rubber supports relieve vibration.

Water pumps are manufactured in China.

Prime PR-H-6900. A device for aeration is installed above the aquarium, in another case, it needs a check valve. The water pump has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 240 l / hour;
  • power – 2.5 W;
  • weight – 0.375 kg.
  • small size;
  • beautiful body;
  • quiet work.

It has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 720 l / hour;
  • power – 10 W;
  • weight – 0.75 kg.
  • there is a performance regulator;
  • the water pump is completely silent;
  • the body is made of polished plastic;
  • The membrane is made of durable rubber.

Schego

The manufacturer is a company from Germany.

SCHEGO IDEAL. A feature of the device is to install above the level of the aquarium. The water pump can work continuously for a long time, it is endowed with the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 250 l / hour;
  • power – 5 W;
  • weight – 0.56 kg.
  • compactness;
  • quiet work;
  • high level of reliability.

. A feature of the work is air pumping to a depth of 2 m. It has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 250 l / hour;
  • power – 5 W;
  • weight – 0.6 kg.
  • complete lack of noise;
  • it is possible to hang the device;
  • regulator control the intensity of aeration.

The water pump is manufactured in Germany.

Eheim 400. The difference is that each flow can be separately controlled. The device has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 400 l / hour;
  • power – 5 W;
  • weight – 0.85 kg.
  • quiet work;
  • high power;
  • There is an adjustment of air flow and the size of the bubbles.
  • high price;
  • low quality membrane, which from time to time will need to be changed.

Can be used for both freshwater and saltwater aquariums. There is a fastening eye for placement on the wall to the water level. Endowed with such characteristics:

  • output channels – 2 pcs ;
  • productivity – 200 l / hour;
  • power – 3.5 W;
  • weight – 0.85 kg.
  • quiet work;
  • there is an adjustment of the size of the bubbles;
  • Suppressed air regulator.
  • for a small aquarium large size.

Aquael

Polish-made water pump.

Aquael AP-100 Plus. The inexpensive and available device which quality is checked by time. Ideal for small aquariums. Endowed with such characteristics:

  • output channels – 1 pc ;
  • productivity – 100 l / hour;
  • power – 2.2 W;
  • weight – 0.208 kg.
  • there are legs that absorb vibration;
  • good price;
  • compactness;
  • durability.
  • high noise level;
  • no air flow adjustment.

. A new representative of a reliable water pump, which has been improved by the manufacturer. Specifications:

  • output channels – 2 pcs ;
  • productivity – 200 l / hour;
  • power – 2.5 W;
  • weight – 0.307 kg.
  • high performance;
  • energy saving;
  • compact size;
  • hardened membrane.

Hydor

Adaptation made in Italy.

Hydor Ario Turbo 1. Suitable for different aquariums. Unique technologies in the development make it durable. It has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 180 l / hour;
  • power – 4.5 W;
  • weight – 0.5 kg.
  • no noise and vibration;
  • it is possible to regulate the air flow;
  • there is an improved finely porous sponge.

Hydor Seltz L20. A high-level product that has the following characteristics:

  • output channels – 2 pcs ;
  • productivity – 700 l / hour;
  • power – 14 W;
  • weight – 0.4 kg.
  • can be used underwater and out of water;
  • suitable for different aquariums;
  • there is a flow adjustment knob;
  • There are suction cups for installation on the glass.

aPump

water pump made in Ukraine.

aPUMP. It is an innovative product with the following characteristics:

  • output channels – 1 pc ;
  • productivity – 100 l / hour;
  • power – 1.5 W;
  • weight – 0,236 kg.
  • stability in continuous use mode;
  • miniature;
  • there is a mount on the suction cups;
  • very quiet work.